2026 Catalog - Flipbook - Page 93
Chain Slings
•
•
Available in sizes 7/32" through 3/4".
Determine wear by measuring cross section at link
ends. If worn to less than the minimum thickness
allowable, chain should be removed from service.
•
Higher capacity may allow use of smaller diameter
chain for your lifts, reducing sling weight and
cost.
Chain
Size
(in.)
Minimum Allowable
Thickness
A (in.)
•
•
Extreme abrasion resistance - more durable.
7/32
0.189
Powder-coated attachments for corrosion
resistance.
9/32
0.239
3/8
0.342
1/2
0.443
5/8
0.546
3/4
0.687
7/8
0.750
1
0.887
1-1/4
1.091
Higher capacity per chain size can be used as an
increased safety factor.
Available in sizes 7/8" through 1-1/4".
Greater temperature tolerance.
All Chain Slings
Meet or exceed all OSHA, ASME, ASTM and
NACM standards.
•
Welded or mechanically assembled.
90°
Rated Capacity For Chain Slings
60°
45°
30°
60°
45°
Size
of Chain
Triple & Quad
Chain Slings*
(lbs.)**
Lifting
Devices
*
Plate
Clamps
** A Quad Chain Sling may not sustain the load evenly on each of its four legs. The maximum working load
limits are therefore set at the same values as the Triple Chain Slings of equal quality and size, and used with
branches at the same angle of inclinations.
Hoist
Rings
Rated Capacity also referred to as Working Load Limit.
When using chain slings in a choke hitch, reduce the sling’s rated capacity by 20%.
1
Lift-All
Hoists
2,700 4,700
3,800 2,700 7,000
5,700
4,000 0.68x0.31 17.8
44
4,300 7,400
6,100 4,300 11,200 9,100
6,400 0.88x0.40 13.6
73
8,800 15,200 12,400 8,800 22,900 18,700 13,200 1.25x0.56 9.6
144
15,000 26,000 21,200 15,000 39,000 31,800 22,500 1.56x0.72 7.7
246
22,600 39,100 32,000 22,600 58,700 47,900 33,900 1.92x0.84 6.3
370
35,300 61,100 49,900 35,300 91,700 74,900 53,000 2.40x1.05 5.0
580
34,200 59,200 48,400 34,200 88,900 72,500 51,300 2.25x1.10 5.3
776
47,700 82,600 67,400 47,700 123,900 101,200 71,500 3.07x1.44 4.5
995
72,300 125,200 102,200 72,300 187,800 153,400 108,400 3.92x1.60 3.7 1,571
Cargo
Control
5.5
7.0
10.0
13.0
16.0
20.0
22.0
26.0
32.0
Double Chain Sling*
(lbs.)
No. Wgt.
Inside
of
per
Nominal
Links 100
Dim.
per
ft.
LxW
ft. (lbs.)
(in.)
Mesh
Slings
Single
Chain
Sling
Grade (in.) (mm.) (lbs.)
7/32
9/32
3/8
1/2
5/8
3/4
7/8
1
1-1/4
30°
Approx.
Nominal
Size
100
100
100
100
100
100
80
80
80
Rigging
Hardware
1
Chain
Slings
•
Minimum thickness
based on ASME
recommendations.
Wire
Rope
•
•
Sling
Protection
Grade 80
Round
Slings
Chain Wear Allowance
Web
Slings
Grade 100
General
Information
CHAIN SLING BASICS
WARNING Do not exceed rated capacities. Sling capacity decreases as the angle from horizontal decreases. Slings should
not be used at angles of less than 30°. Refer to the chain chart on this page and the E昀昀ect of Angle chart in the General Information
section of this catalog.
91
